Stocks List

« Previous 1 2 3 4 Next » Show All Showing 1 - 25 Records 90 Stock(s) Found!

GENERAL CATEGORY : MACHINE TOOLS CATEGORY : FORGING PRESSES SUB CATEGORY : HOT FORGING PRESSES       TYPE : HOT FORGING PRESS
PHOTO
STOCK NO
MAKE
MODEL
YEAR
SERIAL NO
SPECIFICATION & CONDITION
PRICE (JPY)
LOCATION
151843 VORONEZH kG-8042 1991 N/A
Capacity: 1600 Ton, Slide Stroke: 300 mm, No. of Stroke: 85 spm, Shut Height: 850 mm, Slide Adjustment: 10 mm, Table Dimensions: Left/right-1260mm ,front/back-1300mm, Slide Dimensions: Left/right-1120 mm, Front/back-1400mm Overall Dimension: Left/right-5640mm, Front/back-4090mm,Height above floor level:6000mm, Main Electric Motor: 90 kW
151842 VORONEZH KB8040 1992 20
Capacity: 1000 Ton, Slide Stroke: 250 mm, No. of Stroke: 90 spm, Shut Height: 560 mm, Slide Adjustment: 20 mm, Table Dimensions: 770*990 mm, Slide Dimensions: 720*720 mm, Top Ejector: 40 mm, Bottom Ejector: 40 mm, Main Electric Motor: 55 kW, Press Weight: 65,150 kg, Press Dimensions (H*W*D): 5145*4350*3500 mm. Note: The press is without Die set
151841 SUMITOMO FPN-1600 N/A N/A
Capacity:1600T, Capacity at 3 mm above bottom dead point: 1600 Tons, Allowable Eccentric Load left/right 220 mm: 1600 Tons, Allowable Eccentric Load front/back 50mm Die Height: 800mm, Stroke: 280 mm, spm: 80 Max.No.Of Operatiom: 25tpm Max.Working Energy:25tpml=9.6tm Slide Area: RL1000mm*FB1050 Bolster Area: RL1070*FB1200mm Upright Side Opening: FB790mm*TB860mm Upright Inner Dimension: RL1100mm. SKO: MODEL:LINER MOTION,CAPACITY:4T,MAX.AT.ADJUST UP:35mm,MIN.AT.ADJUST DOWN:28mm,pIN NO:1 PCS. BKO: MODEL:CAM&AIR CYCLINDER,CAPACITY:6T,ABILITY FOR UPPER LIMIT MAINTENANCE:30mm,STROKE:60mm,PIN NO:3PCS. AIR: CLEAN&DRY AIR,MIN.GUARANTEED AIR PRESSURE:5.0Kg/cm2,max.pressure:7.0kg/cm2. POWER:440V,220V,60Hz,CONTROL CIRCUIT:110V 60Hz,MAIN MOTOR:75Kw*4pole220v,WITH 200T TRIMMING PRESS
151780 SUMITOMO FP2-800-118 N/A E28728-7
Capacity: 800t, Stroke: 200mm SPM: 60, Die Height: 500mm, Bolster Size: 1100mm X 850mm, Slide Area: 1100*800mm, Slide Adjustment: 5mm, Main Motor: 37 Kw
JAPAN
151762 SMERAL LMZ-2500 1991 N/A
Capacity: 2500 T, Stroke length: 300 mm, Stroke per minutes: 70 SPM, Die Height: 910 mm, Ram Adjustment: 10 mm, Table size (LRxFR): 1420 x 1400 mm, Ram size (LRxFR): 1350 x 1250 mm
JAPAN
151674 SMS-EUMCO-HASENCLEVER (GERMANY) KP16000 N/A N/A
Ø Capacity: 16000 Ton Ø RAM Stroke: 600 mm Ø RAM Adjustment: 30 mm Ø Idle speed: Max. 25 min-1 Ø Number of single stroke: Max. 5 min-1 Ø Shut Height (ram down, adjustment up): approx. 2,000 mm Ø Horizontal daylights between stands: approx. 2,500 mm Ø Table surface: Width – approx. 2,440 mm / Depth-center – approx. 3,000 mm Ø RAM surface: Width – approx. 2,380 mm / Depth-center – approx. 2,800 mm Ø Side window: Width x Height 1,700 x 2,300 mm Ø Drive motor: 700 kW Ø Weight of Press: 1750 Ton Ø Other technical specifications and the photos are attached herewith for your reference
151663 AIDA PK-VK-40(8) N/A N/A
Capacity: 400t, Stroke: 140mm SPM: 45, Die Height: 370mm Bolster Size: 480mm X 600mm Slide Area: 370*500mm Slide Adjustment: 15mm Main Motor: 30 Kw
JAPAN
151660 SMERAL LZK-1000 1985 67134
CAPACITY : 1000TON
JAPAN
151659 KURIMOTO C2F-1600 1981 N/A
CAPACITY : 1600TON, STROKE; 280, 75 SPM, DIE HEIGHT :765, ADJUST; 10 BOLSTER SIZE; 1240X1140 SIDE OPEN SIZE; 920X920 WITH KNOCK OUT
JAPAN
151658 KURIMOTO k-1500 1981 N/A
CAPACITY : 1500 TON, STROKE; 250 DIE HEIGHT; 700 35 SPM ADJUST; 10 BOLSTER SIZE; 1100X1000 SIDE OPEN SIZE; 450X400 WITH KNOCK OUT ALUMINIUM, WARM, COLD, KNUCKLE, HOT FORGING
JAPAN
151648 NATIONAL MAXI 6000 EB N/A N/A
6000t HOT FORGING PRESS + 500t TRIMMING PRESS Make : National (U.S.A). YOM : 1967 Stop Year : 2020 Final maintenance year : 2019 Production : Crankshaft Stroke : 457.2mm SPM : 36 Shut height Max : 1143mm per min - Min1120.8mm Opening of front : 1828.8mm (LR) * 1143mm(H) Opening of side : 965.2mm(FR) * 1092.3mm (H) KO Stroke : upper 101.6mm, below 203.2mm ( Dimensions) : 6000mm (W) * 5664mm (L)* 9169mm (H) Weight : approx 520T Installation space of press : 6198mm ( LR)* 5232mm (FR) Installation space of total equipment approx : 13m*24m 500t Trimming Press ( one gear part is missing) Make : Natori (Japan) Stroke : 300mm SPM : 20 Die Height : 950mm ( in case of adjust up) Ram adjustment : 130mm Main motir : 50hp (3000v) Diemensions : 2500mm (W) * 2812 mm (L) * 770mm (H) Weight approx : 55 t
JAPAN
151583 VORONEZH KB 8546 1987 11
Capacity: 4000T, Ram stroke: 400(+/- 1.0), Distance from table to ram upper shoe when ram is at bottom of stroke: 1000 mm, Ram to table adjustment range: 10 (+/- 0.5), upper knockout: Capacity: 8T, Stroke: 65 mm, Bottom Knockout: capacity: 12.5T, Stroke: 65 mm, Table dimensions (LR x FR): 1710 x 1620 mm, Ram dimensions (LR x FR): 1420 x 1420 mm, Dimensions of opening in press racks: Min height: 1100 mm, Min. width: 1100 mm, Press overall dimensions: LR: 6228 (+/- 50) mm, FR: 5515 (+/- 50) mm, Height above floor level: 7790 (+/- 80) mm, Press mass: 361370 (+/- 3%) kg, Compressed air consumption per ram stroke: 115 cu.dm, Air pressure in air-pressure system MPa(kgf/sq. cm): min - 0.5 (5), max - 0.7 (7), No. of electrical motors: 4, Main drive electric motors: Power: 160 kW, Speed: 975 rpm, Shut height adjustment mechanism electric motors: Power: 5 kW, Speed: 720 mm, oil lubricating station electric motors: Power: 1.1 kW, Speed: 1400 rpm, Grease lubricating station electric motors: Power: 0.4 kW, Speed: 1400 rpm
JAPAN
151559 KURIMOTO C2F-30W N/A N/A
Capacity: 3000 Ton, BDC : 5 mm, Stroke Length : 360 mm, SPM: 60, Die-Height: 1200 mm, Slide Adjustment: 10 mm, Bolster size: 2000*1500 mm, Slide size: 1880*1500 mm
151557 KURIMOTO SMERAL LKM-1600 1976 N/A
Pressure Capacity at 7 mm above bottom dead point:1600 Tons,Stoke: 280 mm,Shut Height(Between bottom Stroke and above adjust point): 760 mm,Ram Adjustment: 10 mm, stroke Speed: 8o SPM,Operation Speed: 22 SPM,Table Size:1248*1140(mm),Ram Size: 920*920 mm,Bottom Knockout Capacity:20 Ton,Air pressure: 5 Kg/cm2,Motor:75 kw
151549 MANYO DLP2500-320S N/A N/A
Capacity: 2500T, Die height: 1020 mm, Stroke Length: 320 mm, Ram Adjustment: 16 mm, Strokes per minute: 20 - 40 mm, Bolster size: 1900 x 1080 mm, Slide size: 1200 x 780 mm, Main Motor: 200 kW AC440V
JAPAN
151494 KURIMOTO SMERAL LKM-1600 N/A 14-444
Capacity at 3 mm above bottom dead point: 1600 Tons, Allowable Eccentric Load left/right 250 mm: 1600 Tons, Stoke: 280 mm, Shut Height: 760 mm, Ram Adjustment: 14 mm, Number of stroke: 85 mm, Production Stroke: 22 mm, Bed Size LR*FR: 1243*1360 mm, Ram Size: 920*1040 mm, Bottom Knock Out capacity at center: 20 Ton, Bottom Knock Out stroke at center: 50 mm, Upper knock-out capacity at center: 20 mm, Upper knock-out stroke at center: 5 kg/cm2, Air pressure: 5 Kg/cm2, Main Motor:75 kw, Lubrication Motor: 0.2 kw, Work Height: 570 mm
151493 NATIONAL MAXI 500 E8 N/A N/A
500 Ton Machine video:https://youtu.be/VPVR--QRr9I
151419 KURIMOTO SMERAL LKM-2500 1969 N/A
Capacity: 2500 ton 3 mm in front of bottom dead point, Stroke:320 mm, Shut height: 890 mm, Ram adjustment: 10 mm, Stroke Speed: 65 SPM, Operation stroke speed: 18 SPM, Table Size:LR x FR 1340 x 1400 mm, Ram size:LR x FR 1040 x 1100 mm, Upper Knock out:5 ton x 50 mm, Bottom Knock out: 25 ton x 70 mm, Main Motor: 110 kw 3000 V x 8P x 50 Hz, Cooling Water: 2 kg/㎠ x 30 L/min, Air pressure: 5 kg/㎠. Note: Machine has been fully refurbished 5 years ago
151375 VORONEZH KB8040 1992 20
Capacity: 1000 Ton, Slide Stroke: 250 mm, No. of Stroke: 90 spm, Shut Height: 560 mm, Slide Adjustment: 20 mm, Table Dimensions: 770*990 mm, Slide Dimensions: 720*720 mm, Top Ejector: 40 mm, Bottom Ejector: 40 mm, Main Electric Motor: 55 kW, Press Weight: 65,150 kg, Press Dimensions (H*W*D): 5145*4350*3500 mm. Note: The press is without Die set
151360 VORONEZH KB8544 N/A N/A
Capacity: 2500T Shut height: 890 mm Table working surface:-1400*1200mm Slide dimensions: -1120*1070mm Slide stroke: 350 mm Slide strokes per minute (continuous): 60 Upper Knock out: -Stroke: 50 mm -Capacity: 6.3t Bottom ejector mechanism: -Stroke: 50 mm -Capacity: 10t Main drive motor power: 130 kW
151323 TMP VORONEZH KB 8048 1990 P3
Capacity: 6300 T, Stroke: 460 mm, SPM: 10, Die Height: 1350 mm, Bolster Size: (Left & Right) 2100 mm (Front & Rear) 1950 mm, Slide Size: (Left & Right) 1900 mm (Front & Rear) 1600 mm, Slide Adjustment: 13 mm, Upper Knock Out:- First Process - Stroke Length: 30 � 5 mm, Capacity: 120 Ton, Second Process - Stroke Length: 30 � 5 mm, Capacity: 160 Ton,Lower Knock Out:- Mechanical Type - Stroke Length: 5 - 20 mm, hydraulic Type - Stroke Length: 10 - 60 mm, Compressed Air Consumption Per Cycle: 115, Press Size: (Left - Right) 7870 mm (Front - Rear) 5750 mm, Press Height from Floor Level: 9500 mm, Press weight: 575800 KG, Total Press Weight: 600 Ton
151028 KURIMOTO SMERAL LKM 2500 N/A N/A
Capacity: 2500 T, Stroke length: 320 mm, Stroke per minutes: 60 SPM, Die Height: 880-890 mm, Ram Adjustment: 10 mm,Table size (LRxFR): 1340 x 1400 mm,Ram size (LRxFR): 1040 x 1100 mm, Upper Knock-out capacity: 5 T, Upper Knock-out Stroke: 50 mm, Lower Knock-out Capacity : 20 T, Lower Knock-out Stroke: 50 mm,Air Pressure: 6 kg/sq.cm
151026 HO SUNG HFP-750 2000 N/A
Capacity:750T,Stroke:180mm,stroke per min:100spm,Slide area LR*FB:720*780mm,Bed area LR*FB:760*900mm,Die height:580mm,Slide adj:8mm,Upper ejector:10mm,Lower ejector:40mm,Main motor(KW*P):45*8
150978 SMERAL LZK 4000A N/A N/A
Capacity:4000T,stroke:380mm,stroke per min:60spm,slide area:1470x1400mm,bed seat:1520x1600mm,slide adjustment:15mm,die height:1000mm,upper ejector:50mm,lower ejector:80mm,main motor:200Kwx8P
150966 KURIMOTO LKM 1000 N/A N/A
Capacity: 1000 T, Stroke length :220 mm, Stroke per min:90 spm,Shut height:680 mm,Ram adjustment:10 mm, Bolster: 995 x 1050 mm, Slide:800 x 800 mm,Bottom knock out:10 T, Motor:55 kW Note: Die- Holder included; Under power, in working condition.
« Previous 1 2 3 4 Next » Show All Page: 1 of 4
90 Stock(s) Found!