TECH CAPACITY : 3000T

STROKE; 355 60 SPM DIE HEIGHT; 934 ADJUST; 10 BOLSTER ; 1450x900,WITH TRANSFER EQUIP. FEED; 260 LIFT; 150 CLAMP; 100 MATERIAL DIA; 40~70 mm PRODUCTS DIA; 170

JAPAN

TECH CAPACITY : 200T

CAPACITY : 200T

japan

TECH CAPACITY : 4000T

Capacity: 4000T, Ram stroke: 400(+/- 1.0), Distance from table to ram upper shoe when ram is at bottom of stroke: 1200 mm, Ram to table adjustment range: 10 (+/- 0.2), upper knockout: Capacity: 8T, Stroke: 82 mm, Bottom Knockout: capacity: 12.5T, Stroke: 82 mm, Table dimensions (LR x FR): 1710 x 1620 mm, Ram dimensions (LR x FR): 1470 x 1100 mm, Dimensions of opening in press racks: Min height: 1100 mm, Min. width: 1100 mm, Press overall dimensions: LR: 6628 (+/- 50) mm, FR: 5700 (+/- 50) mm, Height above floor level: 7830 (+/- 80) mm, Press mass: 366583 (+/- 3%) kg, Compressed air consumption per ram stroke: 115 cu.dm, Air pressure in air-pressure system MPa(kgf/sq. cm): min - 0.5 (5), max - 0.7 (7), No. of electrical motors: 4, Main drive electric motors: Power: 160 kW, Speed: 975 rpm, Shut height adjustment mechanism electric motors: Power: 5 kW, Speed: 720 mm, oil lubricating station electric motors: Power: 1.1 kW, Speed: 1400 rpm, Grease lubricating station electric motors: Power: 0.4 kW, Speed: 1400 rpm

japan

TECH CAPACITY : 1600T

capacity: 1600T

JAPAN

TECH CAPACITY : 1600T

Capacity: 1600 Ton, Slide Stroke: 300 mm, No. of Stroke: 85 spm, Shut Height: 850 mm, Slide Adjustment: 10 mm, Table Dimensions: Left/right-1260mm ,front/back-1300mm, Slide Dimensions: Left/right-1120 mm, Front/back-1400mm Overall Dimension: Left/right-5640mm, Front/back-4090mm,Height above floor level:6000mm, Main Electric Motor: 90 kW

TECH CAPACITY : 1000T

Capacity: 1000 Ton, Slide Stroke: 250 mm, No. of Stroke: 90 spm, Shut Height: 560 mm, Slide Adjustment: 20 mm, Table Dimensions: 770*990 mm, Slide Dimensions: 720*720 mm, Top Ejector: 40 mm, Bottom Ejector: 40 mm, Main Electric Motor: 55 kW, Press Weight: 65,150 kg, Press Dimensions (H*W*D): 5145*4350*3500 mm. Note: The press is without Die set

TECH CAPACITY : 1600T

Capacity:1600T, Capacity at 3 mm above bottom dead point: 1600 Tons, Allowable Eccentric Load left/right 220 mm: 1600 Tons, Allowable Eccentric Load front/back 50mm Die Height: 800mm, Stroke: 280 mm, spm: 80 Max.No.Of Operatiom: 25tpm Max.Working Energy:25tpml=9.6tm Slide Area: RL1000mm*FB1050 Bolster Area: RL1070*FB1200mm Upright Side Opening: FB790mm*TB860mm Upright Inner Dimension: RL1100mm. SKO: MODEL:LINER MOTION,CAPACITY:4T,MAX.AT.ADJUST UP:35mm,MIN.AT.ADJUST DOWN:28mm,pIN NO:1 PCS. BKO: MODEL:CAM&AIR CYCLINDER,CAPACITY:6T,ABILITY FOR UPPER LIMIT MAINTENANCE:30mm,STROKE:60mm,PIN NO:3PCS. AIR: CLEAN&DRY AIR,MIN.GUARANTEED AIR PRESSURE:5.0Kg/cm2,max.pressure:7.0kg/cm2. POWER:440V,220V,60Hz,CONTROL CIRCUIT:110V 60Hz,MAIN MOTOR:75Kw*4pole220v,WITH 200T TRIMMING PRESS

TECH CAPACITY : 800T

Capacity: 800t, Stroke: 200mm SPM: 60, Die Height: 500mm, Bolster Size: 1100mm X 850mm, Slide Area: 1100*800mm, Slide Adjustment: 5mm, Main Motor: 37 Kw

JAPAN

TECH CAPACITY : 2500T

Capacity: 2500 T, Stroke length: 300 mm, Stroke per minutes: 70 SPM, Die Height: 910 mm, Ram Adjustment: 10 mm, Table size (LRxFR): 1420 x 1400 mm, Ram size (LRxFR): 1350 x 1250 mm

JAPAN

TECH CAPACITY : 16000T

Ø Capacity: 16000 Ton Ø RAM Stroke: 600 mm Ø RAM Adjustment: 30 mm Ø Idle speed: Max. 25 min-1 Ø Number of single stroke: Max. 5 min-1 Ø Shut Height (ram down, adjustment up): approx. 2,000 mm Ø Horizontal daylights between stands: approx. 2,500 mm Ø Table surface: Width – approx. 2,440 mm / Depth-center – approx. 3,000 mm Ø RAM surface: Width – approx. 2,380 mm / Depth-center – approx. 2,800 mm Ø Side window: Width x Height 1,700 x 2,300 mm Ø Drive motor: 700 kW Ø Weight of Press: 1750 Ton Ø Other technical specifications and the photos are attached herewith for your reference